160 tons hydraulic punch pressIt is an efficient and precise stamping equipment. The machine uses liquid as the medium to transfer energy, has flexible control, easy automation, uniform and stable running speed, adjustable and controllable speed and pressure compared with other punching equipment, large output adjustment range, strong independence, more stable performance, and can greatly improve product stamping quality.
160 tons hydraulic punch technical parameters:
Model: YWH21-160T
Nominal pressure: 1600KN
Large liquid pressure: 25MPa
Slider stroke: 180mm
Slider work times: 10-40mm
Opening height: 520mm
Stroke adjustment: 110 mm/s
Table height from the ground: 920mm
Fast down speed: 230 mm/s
Working speed: 10 mm/s
Return speed: 170 mm/s
Workbench size: 1000*560mm
160 tons hydraulic punch press
液压冲床是一种依靠液压油为介质通过电机运转带动油泵，液压阀控制方向，油缸施加压力的低噪音型压力机．山东众友重工是一家专业生产液压冲床油压机厂家，其性能稳定，由于是开口式，所以在冲压产品时放料，取料简单方便．操作空间大，能更好的缩短工人的操作时间，从而达到节约人工，提高效率等优点。
160 tons of hydraulic punch technical performance characteristics:
1. The reduction ratio of the reduction mechanism is adopted to increase the required speed of the motor and reduce the required torque of the motor. With the labor-saving linkage mechanism, the required servo motor power can be reduced to less than 40% of the direct drive type, achieving the purpose of energy saving and power saving.
2. When the capacity occurs, the labor-saving connecting rod can effectively amplify the torque input by the servo motor (input end) through the special connecting rod angle and structure to meet the demand of stamping (output end) torque.
3. The flywheel and clutch brake are eliminated, and the structure is simplified, so the power consumption is greatly reduced. Energy saving can reach and 30% ~ 60%.
4, C- type servo 100 tons hydraulic punch stroke can control and adjust the slider speed, so in the middle of the stamping control slider to stop, and reduce its speed into the sheet, so as to achieve the purpose of reducing noise, usually noise reduction effect of up to 10 decibels. In addition, the impact when the slider enters the sheet metal can be reduced, thereby extending the service life of the mold.
5. The stroke and speed of the slider can be adjusted arbitrarily. The forming action set in the program close to the bottom dead center can be used as the slow speed, while the speed before the processing area and the leaving speed after forming can be used as the fast movement. In this way, even if the processing area speed is slowed down to the ideal forming speed, the production efficiency can be improved by about 1/3 compared with the conventional one.
Hydraulic punch manufacturers
The number of strokes of the slider of the 160-ton hydraulic punch is 10-40, and the stroke adjustment amount is 180 mm/s. The number of strokes of the slider of the domestic hydraulic punch press is usually divided into three-gear slider strokes below 100spm, which is called low speed. The number of slider strokes 100-300spm is called medium speed; The number of slider strokes above 300spm is called high speed. The number of strokes of the slider of the hydraulic punch directly affects the structure of the machine tool, the arrangement of the transmission system and the flywheel speed (for crankshaft vertical). High number of strokes-(small transmission ratio) There are few transmission stages, and the flywheel may be set on the crankshaft. Since the size of the flywheel cannot be increased, the energy released by the flywheel during operation is limited to a certain extent. The number of strokes is low-(large transmission ratio) The number of transmission stages increases, and the flywheel can be set on the transmission shaft. Because the transmission shaft has a high speed and the same size, the energy released is large.
Shandong Zhongyou Heavy Industry Hydraulic Punch After-sales Service:
1, responsible for the guidance of the equipment installation and commissioning.
2. Provide training for equipment maintenance personnel of the buyer.
3, the sale of equipment to provide a one-year warranty (except for vulnerable parts), life-long maintenance.
4. Establish computer management files for users and pay regular return visits.
5, set up customer satisfaction telephone, at any time to accept user consultation.
6. After-sales service personnel distributed in various places will immediately solve the problems arising from the use of users.